Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
Have you been trying to locate advise concerning A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a new one is likewise a reasonably challenging task. If the old tub is easily accessible, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and place the brand-new tub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the new one. Make certain you have actually qualified on your own for the work and are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one before you start. Opportunities are you might require a professional plumber to make tube connections.
This post will certainly help you install a brand-new bath tub in your washroom if you have already gotten a brand-new bathtub and don't need to alter the setup of your previous water pipes.
Your tools and material list need to consist of the following:
Planning for the Installation
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be quite troublesome due to the limited accessibility that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipelines. When the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub till the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the water and check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the tub as well as additionally examine the overflow outlet and the typical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has actually been made use of at least once as this will settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making certain that the washing machines remain in location in between the tap and the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind must be linked to the tap ends initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall in between the bathroom and the tiling, leading to difficulties with moisture and feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very eager about How to Install a Bathtub and I really hope you enjoyed reading our piece. Those who enjoyed reading our blog posting kindly be sure to pass it around. Thank you for your time invested reading it.
Visit Link Report this page